If you find CarComplaints.com is helpful ... We rely completely on word of mouth. Talk about us on Facebook, Twitter, tell your mother-in-law. Help us help more people.

Recall List for the 2000 Chrysler Sebring

Official recall notices have been issued for the 2000 Chrysler Sebring by the NHTSA. The complete details of all recalls are listed below, along with what they cover and the recommended solutions. It's important to note that most recalls won't cost you anything to get fixed, so if your car is affected you should call an authorized Chrysler service shop immediately!

  1. 2000 Chrysler Sebring SUSPENSION:FRONT:CONTROL ARM:LOWER ARM, SUSPENSION:FRONT:CONTROL ARM:LOWER ARM NHTSA Campaign #10E059000

    • Date Announced: DECEMBER 27, 2010
    • Vehicles Affected: 22,689

    Summary: Federal-mogul is recalling certain replacement control arm assemblies, part numbers K7425, 10945, fa4510X, K7427, 10946, and fa4611X, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.

    Consequence: If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.

    Actions: Federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on January 28, 2011. Owners may contact federal-mogul at 1-877-489-6659. For detailed information & supporting documents, see the official NHTSA page concerning recall #10E059000 »

  2. 2000 Chrysler Sebring SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT NHTSA Campaign #09E056000

    • Date Announced: OCTOBER 09, 2009
    • Vehicles Affected: 5,787

    Summary: Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, D10945, D10946, G10945, and G10946. The affected control arms, D10945 and D10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The G10945 and G10946 are the same part as the D10945 and D10946 respectively. They are labeled differently depending on the aftermarket customer.

    Consequence: Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.

    Actions: Qualis automotive will replace the ball joints free of charge. The safety recall began on November 9, 2009. Owners may contact qualis automotive at 1-800-493-4128. For detailed information & supporting documents, see the official NHTSA page concerning recall #09E056000 »

  3. 2000 Chrysler Sebring EQUIPMENT NHTSA Campaign #09E043000

    • Date Announced: JULY 07, 2009
    • Vehicles Affected: 30,351

    Summary: Import products is recalling 30,351 fuel filters sold to and branded by the affinia group as Carquest P/N 86523, Napa P/N 3523, and Wix P/N 33523 for use as replacement equipment on the vehicles listed above. These filters may develop a leak in the hose assembly and/or connectors due to improperly adhered line connectors.

    Consequence: This condition may result in a vehicle fire.

    Actions: The affinia group will notify owners and the filters will be replaced free of charge. The safety recall began on August 1, 2009. Owners may contact Wix filter return center at 1-704-869-7411 or import products at 1-508-279-8207. For detailed information & supporting documents, see the official NHTSA page concerning recall #09E043000 »

  4. 2000 Chrysler Sebring EXTERIOR LIGHTING NHTSA Campaign #09E012000

    • Date Announced: APRIL 07, 2009
    • Vehicles Affected: 16,270

    Summary: Sabersport is recalling 16,270 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of Federal Motor Vehicle Safety Standard no. 108, "lamps, reflective devices, and associated equipment." These lamps do not contain the required amber side reflectors.

    Consequence: Decreased lighting visibility may result in a vehicle crash.

    Actions: Sabersport will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on May 11, 2009. Owners may contact sabersport at 1-909-598-7589. For detailed information & supporting documents, see the official NHTSA page concerning recall #09E012000 »

  5. 2000 Chrysler Sebring FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP NHTSA Campaign #07E055000

    • Date Announced: JULY 26, 2007
    • Vehicles Affected: 222

    Summary: Certain Airtex fuel pump module assemblies, P/N E7081H, sold for use as replacement equipment for the vehicles listed above. The wall of the flared fitting of the fuel pump is not thick enough to prevent the mating threaded fittings from bottoming out before an adequate seal is achieved. This condition may result in leakage of fuel at the connection of the vehicle fuel line and the fuel pump module assembly.

    Consequence: In the presence of an ignition source, a fuel leak could result in a fire.

    Actions: Airtex will notify owners and replace the fuel pumps free of charge. The recall is expected to begin during July 2007. Owners can contact Airtex automotive at 800-880-3056. For detailed information & supporting documents, see the official NHTSA page concerning recall #07E055000 »

  6. 2000 Chrysler Sebring FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP NHTSA Campaign #06E088000

    • Date Announced: OCTOBER 23, 2006
    • Vehicles Affected: 39,243

    Summary: Certain tigas fuel pump modules manufactured between June 1 and September 24, 2006, sold under various brand names and P/nos. These fuel pump modules are sold as aftermarket for use in certain DaimlerChrysler vehicles listed above. Silicone material used in manufacture of the flapper valve was out-of-specification, leading to excess swell of the flapper valve restricting the flow of fuel to the fuel pump module.

    Consequence: Fuel restriction could result in loss of power and/or engine stall, possibly resulting in a vehicle crash.

    Actions: Ti automotive will notify owners and replace the defective fuel pump modules free of charge. The recall began on October 6, 2006. Owners may contact ti automotive toll-free at 1-877-461-1834. For detailed information & supporting documents, see the official NHTSA page concerning recall #06E088000 »

  7. 2000 Chrysler Sebring EXTERIOR LIGHTING NHTSA Campaign #06E064000

    • Date Announced: JULY 17, 2006
    • Vehicles Affected: 4,029

    Summary: Certain tradesonic combination lamps sold as replacement lamps for use on the above listed passenger vehicles. Combination lamps not equipped with amber side reflectors fail to conform with the requirements of Federal Motor Vehicle Safety Standard no. 108, lamps, reflective devices, and associated equipment.

    Consequence: Lack of amber side reflectors in the lamps will decrease lighting visibility to other drivers and may possibly result in a vehicle crash.

    Actions: Tradesonic will notify owners and replace the lamps free of charge. The recall is expected to begin during July 2006. Owners may contact tradesonic at 626-934-8884. For detailed information & supporting documents, see the official NHTSA page concerning recall #06E064000 »

  8. 2000 Chrysler Sebring SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT NHTSA Campaign #00V421002

    • Date Announced: DECEMBER 18, 2000
    • Vehicles Affected: 393,796

    Summary: Vehicle description: Passenger vehicles. If the rubber boots on the lower lateral arm ball joints of the front suspension were damaged during assembly, dirt and water can intrude. Also, mmc has added the potential of leaking moisture, which can cause the ball stud to corrode.

    Consequence: This condition could cause the lower lateral arm ball joint to separate, increasing the risk of a vehicle crash. This campaign supercedes mmc's previous safety recall campaign, see 99V-066.

    Actions: Dealers will inspect the lower lateral arm ball joint for wear. Ball joints that exhibit wear beyond the established tolerance will be replaced with newly designed lateral arm ball joints. Ball joints that are within the established tolerance will be cleaned and a special sealant will be applied to prevent intrusion of moisture. For detailed information & supporting documents, see the official NHTSA page concerning recall #00V421002 »

Browse Other Sebring Years

Become a Fan & Spread the Word