If you find CarComplaints.com is helpful ... We rely completely on word of mouth. Talk about us on Facebook, Twitter, tell your mother-in-law. Help us help more people.

Recall List for the 2006 Chrysler Sebring

Official recalls have been issued for the 2006 Chrysler Sebring by the NHTSA. The complete details of all recalls are listed below, along with what they cover and the recommended solutions.

Recalls don't cost you anything to get fixed, but most are time-limited, so if your car is affected you should call your local Chrysler service department immediately!

If you have questions about a recall, write down your VIN & then call Chrysler customer service.

  1. 2006 Chrysler Sebring SUSPENSION:FRONT:CONTROL ARM:LOWER ARM NHTSA Campaign #10E059000

    • Date Announced: DECEMBER 27, 2010
    • Vehicles Affected: 22,689

    Summary: Federal-mogul is recalling certain replacement control arm assemblies, part numbers K7425, 10945, fa4510X, K7427, 10946, and fa4611X, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.

    Consequence: If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.

    Actions: Federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on January 28, 2011. Owners may contact federal-mogul at 1-877-489-6659. For detailed information & supporting documents, see the official NHTSA page concerning recall #10E059000 »

  2. 2006 Chrysler Sebring SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT NHTSA Campaign #09E056000

    • Date Announced: OCTOBER 09, 2009
    • Vehicles Affected: 5,787

    Summary: Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, D10945, D10946, G10945, and G10946. The affected control arms, D10945 and D10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The G10945 and G10946 are the same part as the D10945 and D10946 respectively. They are labeled differently depending on the aftermarket customer.

    Consequence: Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.

    Actions: Qualis automotive will replace the ball joints free of charge. The safety recall began on November 9, 2009. Owners may contact qualis automotive at 1-800-493-4128. For detailed information & supporting documents, see the official NHTSA page concerning recall #09E056000 »

  3. 2006 Chrysler Sebring SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER NHTSA Campaign #07E023000

    • Date Announced: MARCH 29, 2007
    • Vehicles Affected: 13,128

    Summary: Certain cardone master cylinders with part numbers 10-2925, 10-2987, 10-2987mza, 10-3083, 11-3015, 11-3042, 11-3044, 11-3045, 11-3047, 11-3064, and 11-3156, and with date codes lower than dca7078 sold as replacement equipment for use on the vehicles listed above. The seal on master cylinder can fail and leak brake fluid.

    Consequence: Loss of brake fluid can result in poor braking performance, possibly resulting in a vehicle crash.

    Actions: Cardone will notify owners and offer to repurchase any defective master cylinders. The recall began during April 2007. Owners can contact cardone at 1-800-777-4780. For detailed information & supporting documents, see the official NHTSA page concerning recall #07E023000 »

Browse Other Sebring Years