- November 4: Mazda Recalls CX-70 and CX-90 SUVs recalls | 10 days ago
- November 4: Mazda Valve Stem Seal Settlement news | 10 days ago
- September 28: Mazda MX-5 Miata Recall Includes 85,000 Cars recalls | 47 days ago
- September 19: Mazda Class Action Lawsuit: 'Depress Brake Pedal to Start Vehicle' news | 56 days ago
- September 17: Mazda Class Action Lawsuit Filed Over Heated Seats news | 58 days ago
2017 Mazda CX-5
815 Technical Service Bulletins (TSBs)
TSB List for the 2017 Mazda CX-5
Technical Service Bulletins (TSBs) for the 2017 CX-5 are official communications between Mazda & their dealerships that describe processes for troubleshooting or fixing certain common problems. All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
STEERING
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #06-001-24
Some customers may complain about a creaking, knocking, rattle or clunk noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. Read More »
-
TSB #06-004-23b
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. Read More »
-
TSB #06-001-23a
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #02-003-22
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #02-003-21-3777
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #06-003-20-3718b
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. Read More »
-
TSB #06-003-20-3718
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. Read More »
-
TSB #06-003-20-3718
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. Read More »
-
TSB #06-002-3705
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and ... Read More »
-
TSB #02-003-20-3677
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure. Read More »
-
TSB #06-003-19-3588
Some customers may notice the heated steering wheel shuts off by itself after approx. 5 - 7 minutes after turning it on. The heated steering wheel is designed to stay on for 30 minutes before shutting off by itself. Read More »
-
TSB #06-001-19-3575
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and ... Read More »
-
TSB #02-004-19-3574
Some customers may complain that the steering wheel is off center more than 3? even when driving straight on a flat road. Read More »
-
TSB #MT-012-18
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
-
TSB #04-007-18-3500
Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. Read More »
-
TSB #06-002-17-3367
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. Read More »
STEERING: STEERING WHEEL/HANDLE BAR
-
TSB #06-003-19-3588
Some customers may notice the heated steering wheel shuts off by itself after approx. 5 - 7 minutes after turning it on. The heated steering wheel is designed to stay on for 30 minutes before shutting off by itself. Read More »
-
TSB #06-001-18-3481
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and ... Read More »
-
TSB #02-010-18-3477
Some customers may complain that the steering wheel is off center more than 3? even when driving straight on a flat road. Read More »
-
TSB #06-001-17-3307a
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance.This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
STEERING:ELECTRIC POWER ASSIST SYSTEM
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
SUSPENSION
-
TSB #02-003-23
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-004-22a
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-002-22
Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. Read More »
-
TSB #02-004-22
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-002/22
Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. Read More »
-
TSB #02-001-21-3766
Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. Read More »
-
TSB #02-007-20-3729
Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-003-19-3547
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
-
TSB #02-001-19-3550
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-013-18-3491
Some vehicles may exhibit a crack on the front shock absorber dust boot (1). This may be caused by the dust boot having insufficient resistance to the cold. Read More »
-
TSB #02-012-18-3482
Some vehicles may exhibit a clunking noise from the front coil springs when driving over bumps. The noise is due to stick-slip between the front strut bearing (1) and the coil spring (2). Read More »
-
TSB #02-005-18-3444
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
-
TSB #06-002-17-3367
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. Read More »
SUSPENSION:FRONT:SHOCK ABSORBER
-
TSB #02-006-18-3449
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-002-18-3300d
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #02-009-17-3392
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
SUSPENSION:FRONT:WHEEL BEARING
-
TSB #SA-006-22
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-016-19
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
SUSPENSION:REAR:SPRINGS:COIL SPRINGS
-
TSB #02-015-18-3499a
Some vehicles may exhibit a knocking noise from the rear coil spring and/or the vehicle body sits lower in the rear. These symptoms may be caused by a broken rear coil spring at its lower side. Read More »
-
TSB #02-015-18-3499
Some vehicles may exhibit a knocking noise from the rear coil spring and/or the vehicle body sits lower in the rear. These symptoms may be caused by a broken rear coil spring at its lower side. Read More »
SUSPENSION:REAR:SHOCK ABSORBER
-
TSB #02-006-18-3449
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
BRAKES (PWS)
-
TSB #SA-003-23a
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #04-001-23b
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. Read More »
-
TSB #SA-003/23
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #04-004-22
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. Read More »
-
TSB #04-002-21-3809
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #04-005-20-3687a
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. Read More »
-
TSB #04-007-20-3713a
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #00-002-19-3561
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
-
TSB #04-002-19-3545
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #00-003-18-3480
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program. Read More »
-
TSB #04-004-18-3468
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #15-006-17-3388
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #SA-052-17
Smart City Brake Support (SCBS) frequently asked questions (FAQ) Read More »
SERVICE BRAKES, HYDRAULIC
-
TSB #SA-016-24
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #04-001-23a
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-078-22
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #04-002-22a
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. Read More »
-
TSB #04-002-22
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #04-007-20-3713
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #04-005-20-3687
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. Read More »
-
TSB #04-003-20-3668
Some vehicles may exhibit grooves (1) in rear brake disc plate(s), as shown below. This concern is mostly found on new or low mileage vehicles, when the brakes are new. Read More »
-
TSB #SA-019-20
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #04-004-19-3622
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #15-001-19-3517a
Some vehicles may experience a SBS/SCBS, LAS/LDWS and/or ADAPTIVE LED headlight /HBC warning light on with the DTC U0155:00 stored in memory. The warning lights may stay on while these functions are deactivated. Read More »
-
TSB #00-003-18-3480a
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
SERVICE BRAKES, AIR
-
TSB #04-001-19-3556
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
SERVICE BRAKES, AIR:DISC:PADS
-
TSB #04-007-20-3713
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
PARKING BRAKE
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #SA-042-18
DO NOT follow the instructions on MGSS for performing the ELECTRIC PARKING BRAKE (EPB) FORCED RELEASE PROCEDURE until these instructions are read, otherwise, damage to the EPB system may occur The instructions on MGSS are incorrect in ... Read More »
PARKING BRAKE:ELECTRICAL
-
TSB #04-004-21-3821
Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. Read More »
-
TSB #04-007-20-3713a
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #04-007-20-3713
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
ENGINE (PWS)
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #07-007-19-3638
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
-
TSB #01-010-19-3582
Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. Read More »
-
TSB #01-007-19-3541
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
-
TSB #01-003-19-3557
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #01-022-18-3528a
Some vehicles may exhibit an excessive body vibration/unusual noise when idling or driving after parking inextremely cold temperatures (-25?C/-13?F). NOTE: This excessive vibration does not occur if the engine mount rubber No. Read More »
-
TSB #09-037-18-3534a
Some vehicles equipped with MAZDA CONNECT may exhibit the following oil maintenance monitor concerns on the center display: The wrench light (Oil Change Due message) cannot be cleared using MAZDA CONNECT/Applications/Vehicle Status ... Read More »
-
TSB #01-021-18-3514a
Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
-
TSB #MT-008-18
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
-
TSB #01-012-18-3474
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-026-18
If a vehicle is driven on extremely short trips most of the time (where the engine never reaches normal operating temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Read More »
-
TSB #01-006-18-3429
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
-
TSB #MT-021-17
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
ENGINE AND ENGINE COOLING
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #01-008-23
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. Read More »
-
TSB #SA-035-23
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #SA-032-23
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-023-23
Some customers may experience any of the following: Engine no start due to battery discharge Ignition cannot be turned OFF Infotainment remains ON after the ignition is turned OFF Infotainment display is blank Commander switch is ... Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #RF-23-01
When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. Read More »
-
TSB #MT-004-22
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
-
TSB #SA-065-22
Some vehicles equipped with a coolant control valve may exhibit difficulties when refilling the coolant because the control valve is closed and air in the engine cannot escape during ignition ON. Read More »
-
TSB #01-012-22
Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. Read More »
-
TSB #SA-044-22
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-050-21a
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. Read More »
-
TSB #MT-002-21
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
-
TSB #07-003-21-3825
Some vehicles may exhibit a squeaking noise from the blower motor while it is operating. This is caused by burrs that were not trimmed completely in the manufacturing process of the blower motor. Read More »
-
TSB #01-006-21-3779a
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #CSP05c
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #CSP05d
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #CSP05b
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #CSP05a
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #MT-005-20
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Read More »
-
TSB #CSP05
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #SA-071-20
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #SA-005-20
THUMPING/RATTLING NOISE FROM ENGINE COMPARTMENT: Some customers may complain about an unusual thumping/rattling noise coming from the engine compartment. Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-053-19
GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Read More »
-
TSB #01-019-19-3628
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #01-017-19-3601
Some customers may complain about a vibration through the driver and passenger seats at idle in (D)rive and (R)everse when the engine rpm drops down to 550. This vibration is caused by: 1.5L The No.3 and No. Read More »
-
TSB #MT-003-19
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #SA-040-19
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #01-016-19-3627
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. Read More »
-
TSB #01-010-19-3582a
Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #01-005-19-3548
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak). Read More »
-
TSB #01-004-19-3558
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
-
TSB #MT-009-18
If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2. Read More »
-
TSB #MT-009-18
If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2. Read More »
-
TSB #SA-029-18
IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Read More »
-
TSB #05-004-18-3466
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #04-003-18-3455
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
-
TSB #SA-047-20a
CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. Read More »
ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS
-
TSB #SA-044-22
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
-
TSB #01-016-18-3522
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
-
TSB #01-013-18-3478
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely ... Read More »
-
TSB #01-006-18-3429
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
-
TSB #01-005-18-3415
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. Read More »
ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
FUEL SYSTEM, GASOLINE
-
TSB #MT-003/22
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. Read More »
-
TSB #01-002/22
Some vehicles may exhibit a fuel odor at the left / rear area of the vehicle while the engine is idling that usually occurs when the fuel tank is warmed up in hot weather and/or after long distance driving. Read More »
-
TSB #MT-002-21a
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #01-005-18-3415
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. Read More »
FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
FUEL SYSTEM, OTHER
-
TSB #MT-002-21a
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
FUEL SYSTEM, OTHER:FUEL FILTER
-
TSB #RF-16-03R1
The SKYACTIV?-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV? oil filters. The unique oil filter can be identified with two white bands as shown below. Read More »
POWER TRAIN
-
TSB #PF-24-03
Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #05-005-23a
Some vehicles may exhibit a chirp noise (stick-slip noise) from the automatic transaxle (AT) when shifting from 3 to 4 while driving. Read More »
-
TSB #05-005-23
Some vehicles may exhibit a chirp noise (stick-slip noise) from the automatic transaxle (AT) when shifting from 3 to 4 while driving. Read More »
-
TSB #05-003-23
Some customers may complain of a shift shock felt when shifting into 3rd, 5th and/or R range with no A/T related DTC stored. Read More »
-
TSB #05-002-23
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-007-23
The rear differential case could develop a crack in the case. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
-
TSB #SA-007/23
The rear differential case could develop a crack in the case NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
-
TSB #SA-068-22
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
-
TSB #01-010-22
Some customers may experience a squeaking noise may be heard from the exhaust manifold when the idle speed drops from fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. Read More »
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-006-22
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-009-22
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. Read More »
-
TSB #SA-050-21a
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. Read More »
-
TSB #05-001-21-3826
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #SA-032-21
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-033-21
The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-047-20b
CRACKED REAR DIFFERENTIAL. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
-
TSB #05-005-20-3752
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-053-20
When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. Read More »
-
TSB #SA-047-20
Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-030-20
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration. Read More »
-
TSB #SA-058-19
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »
-
TSB #SA-053-19
GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Read More »
-
TSB #05-004-19-3466
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #05-002-19-3576
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #05-002-18-3454
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
-
TSB #SA-010-18
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
-
TSB #05-002-23
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #01-010-19-3582
Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. Read More »
-
TSB #MT-014-17
Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging. Read More »
POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
POWER TRAIN:DRIVELINE:UNIVERSAL JOINT
-
TSB #03-002-18-3505a
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
POWER TRAIN:DRIVELINE:DRIVESHAFT
-
TSB #03-001-19-3505b
Some vehicles may exhibit a squeak noise from the right front driveshaft at the automatic transaxle when driving. Read More »
-
TSB #03-002-18-3505a
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
-
TSB #03-002-18-3505
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT
-
TSB #SA-009-22
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. Read More »
POWER TRAIN:AXLE ASSEMBLY
-
TSB #05-002-19-3576
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #SA-037-18
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
ELECTRICAL SYSTEM
-
TSB #07-003-24
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-008-24
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-032-23
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-033-23
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-023-23
Some customers may experience any of the following: Engine no start due to battery discharge Ignition cannot be turned OFF Infotainment remains ON after the ignition is turned OFF Infotainment display is blank Commander switch is ... Read More »
-
TSB #09-016-23
Speedometer replacement procedure Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #07-002-23
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: * Ghost Touch * DTC B108E:04 may be stored (Touch screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White ... Read More »
-
TSB #09-018-22b
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.324 or later). The system performance has been improved as follows: Ver. 74.00. Read More »
-
TSB #22-01R
Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Read More »
-
TSB #09-003-22b
Some vehicles may exhibit the following malfunctions: - The film on the center display is peeling off, as shown in the illustration below. This may be caused by cleaning the center display surface. Read More »
-
TSB #SA-075-22
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-074-22
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. Read More »
-
TSB #15-002-22a
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. Read More »
-
TSB #SA-066-22
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of ... Read More »
-
TSB #SA-067-22
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * ... Read More »
-
TSB #RF-22-01
Some customers may complain about infotainment center display ghost touch (touch screen operates by itself), surface peeling or spider cracks. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-041-22
Some customers may complain about infotainment center display: - Ghost Touch (Touch screen operates by itself) - Surface Peeling - Spider Cracks Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-22d
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-006-22
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #09-018-22
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.311 or later). Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-026-22
Apple CarPlay / Android Auto Frequently Asked Questions (FAQs) Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-003/22
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #SA-001-22
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-003/22
Some vehicles may exhibit the following malfunctions: 1. The film on the center display is peeling off, as shown in the illustration below. This may be caused by cleaning the center display surface. Read More »
-
TSB #09-004/22
Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
-
TSB #15-002/22
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. Read More »
-
TSB #15-001/22
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #01-006-21-3779b
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #SA-052-21
For improvement of electrical diagnosis, the SKYACTIV??A? Wiring Terminal Test Kits has been delivered all the dealers. Read More »
-
TSB #SA-050-21a
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. Read More »
-
TSB #07-004-21-3830
Some vehicles may exhibit insufficient A/C performance / insufficient airflow from vents or ducts. These concerns may be caused by an evaporator temperature sensor malfunction due to insufficient water-proofing. Read More »
-
TSB #SA-019-21d
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-019-21c
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-046-21
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #15-002-21-3812
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #SA-019-21a
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-029-21a
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #09-017-21-3808
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black under any temperature. Read More »
-
TSB #09-015-21-3805
Some CX-5 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #08-002-21-3788
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #01-005-21-3778
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #01-006-21-3779
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #MT-006-20
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #09-036-20-3756
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH??A? hands-free unit or text messaging related concerns. Read More »
-
TSB #SA-070-20
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #SA-063-20
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage. Read More »
-
TSB #MT-003-20
Some customers may complain about an inoperative power liftgate (PLG) and the any of the following DTC's stored in memory: ??A?A? U3003:16 (Power liftgate (PLG) control module power supply voltage low input) ??A?A? U3003:17 (Power ... Read More »
-
TSB #06-003-20-3718
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. Read More »
-
TSB #MT-001-20
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #08-001-20-3696a
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. ??A?A? DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #09-015-20-3698b
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #09-019-20-3686
Some customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
-
TSB #09-015-20-3698
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #SA-041-20
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-011-20a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #01-002-20-3678
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #SA-011-20
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #09-003-20-3671
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #07-007-19-3638
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #09-031-19-3625
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-029-19
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #SA-001-19b
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-001-19a
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers. Read More »
-
TSB #05-001-19-3538
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Read More »
-
TSB #09-010-19-3577
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-002-19-3542
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #SA-006-19
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #15-001-19-3517
Some vehicles may experience a SBS/SCBS, LAS/LDWS and/or ADAPTIVE LED headlight /HBC warning light on with the DTC U0155:00 stored in memory. The warning lights may stay on while these functions are deactivated. Read More »
-
TSB #01-006-19-3549
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Read More »
-
TSB #01-001-19-3551
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-002-19-3552
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #15-002-18-3502a
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #MT-011-18
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #09-037-18-3534a
Some vehicles equipped with MAZDA CONNECT may exhibit the following oil maintenance monitor concerns on the center display: The wrench light (Oil Change Due message) cannot be cleared using MAZDA CONNECT/Applications/Vehicle Status ... Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-007-18
Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #09-035-18-3509
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-042-18
DO NOT follow the instructions on MGSS for performing the ELECTRIC PARKING BRAKE (EPB) FORCED RELEASE PROCEDURE until these instructions are read, otherwise, damage to the EPB system may occur The instructions on MGSS are incorrect in ... Read More »
-
TSB #SA-036-18
MAZDA MOBILE START (MMS) APP ERROR MESSAGE INSTALLED ON ANDROID DEVICES: Customers may get an error message "Device no longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Read More »
-
TSB #MT-004-18
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
-
TSB #15-002-18-3502
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #MT-006-18
POWER LIFTGATE INOPERATIVE WITH DTC U3003:16: Some customers may complain about an inoperative power liftgate (PLG) with DTC U3003:16 (Power liftgate (PLG) control module power supply voltage low input) is stored in memory. Read More »
-
TSB #SA-013-18
Some customer's may complain that the blind spot monitoring (BSM) is not operating, and the key ON bulb check is OK with no DTCs stored in memory. Read More »
-
TSB #09-010-18-3440a
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.546 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #SA-006-18
Some customer may complain about multiple warning lights illuminated. Additional symptoms may include: Engine will not turn OFF, Power Liftgate will not open, DSM HU/CM network test failure, Any of the following DTC?s stored: This may be ... Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-001-18
When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping. Read More »
-
TSB #15-006-17-3388a
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #01-001-17
Some vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery ... Read More »
-
TSB #MT-020-17
The MODE switch operation for the Mazda Radar Cruise Control (MRCC) system has been changed as follows: Previous - Press the MODE switch to switch to the cruise control function. Read More »
-
TSB #SA-069-17
If you receive a customer complaint of an excessive gap between decoration panel and switch panel (as shown below), repair it according to the repair procedure below. Read More »
-
TSB #MT-017-17
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #15-006-17-3388
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #09-017-17-3347c
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-064-17
Some customers may complain about one or more warning lights on when they start the vehicle during hot weather. The combination of warning lights mentioned by the customer may include: SCBS, LDWS, HBC. Read More »
-
TSB #09-001-17-3296b
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
-
TSB #RF-17-05
There is a minor error with the Controller Programming instructions included with the accessory remote start kit C960-V7-620. In the current "Registration (programming) of the controller" instructions, step 5 shows an incorrect image. Read More »
-
TSB #MT-014-17
Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging. Read More »
-
TSB #SA-048-17
In order to do a CMU data retrieval for the new MAZDA CONNECT software, make sure to use version 31 (available on MGSS). Read More »
-
TSB #09-019-17
Fctry MESSASGE DISPLAYED after instrument cluster replacement. After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Read More »
-
TSB #09-018-17
Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
-
TSB #ONP07
Owner Notification program ONP07 Mazda mobile start (MMS) system Read More »
-
TSB #SA392
Stopper plates for air bag module connectors have been established as new service parts Read More »
-
TSB #RF-17-01
All models - Stopper plates for air bag module coinnectors Read More »
-
TSB #SA266
MAZDA Mobile start (MMS) cannot communicate with vehicle Read More »
-
TSB #08-004-16
M-MDS Data monitor displays incorrect air bag module resistance value. Read More »
-
TSB #SA234
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab. Read More »
ELECTRICAL SYSTEM:12V/24V/48V BATTERY
-
TSB #08-002-23
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #01-006-21-3779a
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #01-008-18-3451
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-009-18-3452
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
ELECTRICAL SYSTEM:IGNITION
-
TSB #05-001-19-3538
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Read More »
-
TSB #SA-049-17
There are a few issues with the accessory C960-V7-620 remote start kit instructions. In the current ?Registration (programming) of the controller? instructions, step 5shows an incorrect image. The function button is the lower button. Read More »
ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
-
TSB #SA-050-23
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #07-002-23
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #15-001-19-3517a
Some vehicles may experience a SBS/SCBS, LAS/LDWS and/or ADAPTIVE LED headlight /HBC warning light on with the DTC U0155:00 stored in memory. The warning lights may stay on while these functions are deactivated. Read More »
-
TSB #09-009-19-3566
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #09-002-18-3410
After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #09-035-17-3080
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #SA-064-17
Some customers may complain about one or more warning lights on when they start the vehicle during hot weather. The combination of warning lights mentioned by the customer may include: SCBS, LDWS, HBC. Read More »
-
TSB #SA-061-17
In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is? 2017 Mazda North American Operations, U.S.A. Read More »
-
TSB #09-019-17
Fctry MESSASGE DISPLAYED after instrument cluster replacement. After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Read More »
-
TSB #09018173351
Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
-
TSB #09-018-17
Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER
-
TSB #09-016-23
Speedometer replacement procedure Read More »
-
TSB #09-024-22
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. Read More »
ELECTRICAL SYSTEM:SOFTWARE
-
TSB #SA-001-22b
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #SA-008-21
DTC P0942:49 is missing from the Workshop Manual on MGSS. Follow the repair procedure below to repair the vehicle until the information is added. Read More »
-
TSB #09-030-20-3740
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #SA-017-18
Upgrade your PCs to IDS version 109.00 and 109.01 from the previous version. NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108. Read More »
-
TSB #SA-016-18
If the MAZDA CONNECT Connectivity Master Unit (CMU) is replaced due to failure, the replacement CMU may have a navigation system software error. To resolve this concern, after the installation of the new CMU, check the software version. Read More »
-
TSB #09-010-18-3440
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.504 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #09-001-18-3387a
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during extremely cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #09-003-18-3405a
Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. Read More »
-
TSB #09-003-18-3405
Some customers may complain that the Voice Recognition system does not recognize "Address" or "NewDestination" navigation voice commands. This may be caused by faulty navigation SD card software. Read More »
-
TSB #SA-036-17
IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version. Read More »
-
TSB #SA-063-17
Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. Read More »
-
TSB #09-017-17-3347b
All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #RF-17-05
There is a minor error with the Controller Programming instructions included with the accessory remote start kit C960-V7-620. In the current "Registration (programming) of the controller" instructions, step 5 shows an incorrect image. Read More »
-
TSB #MT-014-17
Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging. Read More »
-
TSB #SA-048-17
In order to do a CMU data retrieval for the new MAZDA CONNECT software, make sure to use version 31 (available on MGSS). Read More »
-
TSB #09-017-17-3347a
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-046-17
An update to the MAZDA CONNECT system is now available for download from the Mazda Global Service Support (MGSS) system. The new version number is 59.00.502. Please refer to TSB 09-017/17 for a list of improvements to the system. Read More »
-
TSB #09017173346
All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #08-002-17-3312
When monitoring the resistance of the air bag modules and pre-tensioner seat belts, the Mazda Modular Diagnostic System (M-MDS) may display a value of only 1/100th of the actual resistance value. Read More »
-
TSB #SA385
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. Read More »
ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SOFTWARE
-
TSB #15-003-21-3828
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. Read More »
ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:SENSORS
-
TSB #15-002/22
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. Read More »
ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:WARNING
-
TSB #15-002/22
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. Read More »
EXTERIOR LIGHTING
-
TSB #09-041-23
Some customers may complain that the headlights get foggy or have water spots inside. This concern may be caused by the anti-fog coating not preventing inner condensation under certain situations. Read More »
-
TSB #09-019-23
Some customers may complain of foggy rear combination lights (as shown below) after a car wash or heavy rain. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-014-19-3581
Some customers may complain of foggy rear combination lights (as shown below) after a car wash or heavy rain. This concern may be caused by water entering into the rear combination lights through the ventilation tubes. Read More »
-
TSB #15-001-19-3517a
Some vehicles may experience a SBS/SCBS, LAS/LDWS and/or ADAPTIVE LED headlight /HBC warning light on with the DTC U0155:00 stored in memory. The warning lights may stay on while these functions are deactivated. Read More »
-
TSB #09-003-19-3555
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #SA-064-17
Some customers may complain about one or more warning lights on when they start the vehicle during hot weather. The combination of warning lights mentioned by the customer may include: SCBS, LDWS, HBC. Read More »
EXTERIOR LIGHTING:HEADLIGHTS
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-011-18-3448
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-001-17-3296b
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
-
TSB #SA-057-17
High Beam Control (HBC) system frequently asked questions (FAQ) Read More »
-
TSB #09-008-17-3324
Take caution when cleaning plastic headlight lenses. Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Read More »
EXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH
-
TSB #SA-023-18
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #SA-066-17
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
EXTERIOR LIGHTING:TAIL LIGHTS
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-014-19-3581
Some customers may complain of foggy rear combination lights (as shown below) after a car wash or heavy rain. This concern may be caused by water entering into the rear combination lights through the ventilation tubes. Read More »
-
TSB #09-032-18-3483
Some customers may complain of foggy rear combination lights (as shown below) after a car wash or heavy rain. This concern may be caused by water entering into the rear combination lights through the ventilation tubes. Read More »
-
TSB #09-011-18-3448
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
VISIBILITY
-
TSB #SA-012-23
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-003-21-3828
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #RF-18-01R1
If one of the blind spot monitoring (BSM) control modules has to be replaced on a 2017-2018 CX-5, inspect the labels (1) and (2) on the modules (P/N KB8C-67-Y30E). Read More »
VISIBILITY:WINDSHIELD
-
TSB #SA-051-20
Some vehicles may experience an engine no start/no crank with either of the following DTC's stored: P0615:12 - Starter relay circuit malfunction B112A:12 - IG2 relay circuit malfunction. Read More »
-
TSB #SA-058-17
CAUTION: DO NOT attempt any repair of the windshield damaged by stone chipping/cracks at the area in front of the Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead. Read More »
VISIBILITY:POWER WINDOW DEVICES AND CONTROLS
-
TSB #SA-039-23a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-040-21
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #MT-003-21
Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. Read More »
VISIBILITY:REARVIEW MIRRORS/DEVICES
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM
-
TSB #SA-012-23
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. Read More »
-
TSB #SA-074-22
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. Read More »
VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:AIR HANDLER/CHAMBER, DUCTS, AND VALVES
-
TSB #07-004-21-3830
Some vehicles may exhibit insufficient A/C performance / insufficient airflow from vents or ducts. These concerns may be caused by an evaporator temperature sensor malfunction due to insufficient water-proofing. Read More »
AIR BAGS
-
TSB #08-002-23
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #08-003-22
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. Read More »
-
TSB #SA-042-21
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
-
TSB #08-001-20-3696a
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. ??A?A? DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #08-001-19-3544
This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service. Read More »
-
TSB #08-001-18-3457
This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service. Read More »
-
TSB #MT-003-18
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
-
TSB #01-001-17
Some vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery ... Read More »
-
TSB #MT-018-17
Some customers may complain about: PASSENGER Seat Belt and PASS AIRBAG OFF indicator lights ON (A). Front seat warmers ON (B) and cannot be turned OFF.No DTC's are stored in memory. Read More »
-
TSB #08-002-17-3312
When monitoring the resistance of the air bag modules and pre-tensioner seat belts, the Mazda Modular Diagnostic System (M-MDS) may display a value of only 1/100th of the actual resistance value. Read More »
AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION
-
TSB #SA-027-18
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION:STATUS INDICATOR LAMP/LIGHT
-
TSB #08-002-23
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
SEAT BELTS
-
TSB #MT-018-17
Some customers may complain about: PASSENGER Seat Belt and PASS AIRBAG OFF indicator lights ON (A). Front seat warmers ON (B) and cannot be turned OFF.No DTC's are stored in memory. Read More »
SEAT BELTS:FRONT:WARNING LIGHT/DEVICES
-
TSB #SA-027-18
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
STRUCTURE
-
TSB #SA-039-23a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-039-23
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-036-23
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
-
TSB #SA-008-22a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #09-003-22a
Some vehicles may exhibit the following malfunctions: - The film on the center display is peeling off, as shown in the illustration below. This may be caused by cleaning the center display surface. Read More »
-
TSB #SA-008-22
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #MT-001-22
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
-
TSB #09-009-21-3759a
Rusty Panel at Bottom (Inner Side) of Doors: Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. Read More »
-
TSB #09-028-21-3748a
Whistling Noise From Front Door Window Glass or Windshield When Driving At Highway Speed: Some customers may complain about a whistling noise heard from the top of the A-pillar area and/or the top of windshield area when driving at ... Read More »
-
TSB #09-016-21-3797c
Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation ... Read More »
-
TSB #09-033-21-3847
Some customers may complain that the rear door seaming welt (1) comes off when stepping in and/or out of the vehicle. Read More »
-
TSB #09-028-21-3748
Some customers may complain about a whistling noise heard from the top of the A-pillar area when driving at highway speeds. Read More »
-
TSB #09-016-21-3797b
Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation ... Read More »
-
TSB #09-016-21-3797a
Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation ... Read More »
-
TSB #09-016-21-3797
Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation ... Read More »
-
TSB #09-009-21-3759
Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. It is caused by mud/sand adhering to the side sill, which scratches the paint surface when the door is opened/closed. Read More »
-
TSB #09-008-21-3791
Some customers may notice the flock finishing on the door sash molding is peeled off (as shown below) when opening the frozen door. Read More »
-
TSB #09-028-20-3733
Some vehicles may have a loose rear bumper reflector without any visible external damage to the rear bumper cover. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #09-034-19-3617
Some vehicles may exhibit cracking (1) at the lower part of the rear side, rear door garnish (2). This concern is caused by excess stress applied to the rear door garnish. Read More »
-
TSB #09-015-19-3578
Some customers may complain that the rear door seaming welt (1) comes off when stepping in and/or out of the vehicle. Read More »
-
TSB #09-008-19-3565
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-014-18-3443a
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-021-18-3459a
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #02-015-18-3499
Some vehicles may exhibit a knocking noise from the rear coil spring and/or the vehicle body sits lower in the rear. These symptoms may be caused by a broken rear coil spring at its lower side. Read More »
-
TSB #SA-013-18
Some customer's may complain that the blind spot monitoring (BSM) is not operating, and the key ON bulb check is OK with no DTCs stored in memory. Read More »
-
TSB #09-014-18-3443
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #02-009-17-3392
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
-
TSB #SA-069-17
If you receive a customer complaint of an excessive gap between decoration panel and switch panel (as shown below), repair it according to the repair procedure below. Read More »
-
TSB #09-001-17-3296b
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
-
TSB #MT-009-17
Some vehicles may exhibit a chattering noise from the rear spoiler (A) while driving on a rough road. This may be caused by loose rear spoiler installation nuts. Read More »
STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS
-
TSB #09-039-18-3520
Some customers may notice the floor under cover No. 2 falling off at the bolt (1) location after driving through snow and/or ice. This may be caused by snow and/or ice accumulation under cover No. 2. Read More »
STRUCTURE:BODY
-
TSB #MT-012-18
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
-
TSB #09-040-18-3537
Some customers may notice the flock finishing on the door sash molding is peeled off when opening the frozen door. This concern may be caused by insufficient durability due to an improper production process of the door sash moldings. Read More »
STRUCTURE:BODY:DOOR
-
TSB #09-029-20-3732
Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become ... Read More »
-
TSB #09-034-19-3617
Some vehicles may exhibit cracking (1) at the lower part of the rear side, rear door garnish (2). This concern is caused by excess stress applied to the rear door garnish. Read More »
-
TSB #09-015-19-3578
Some customers may complain that the rear door seaming welt (1) comes off when stepping in and/or out of the vehicle. Read More »
-
TSB #09-030-18-3484
Some customers may complain that the rear door seaming welt (1) comes off when stepping in and/or out of the vehicle. Read More »
-
TSB #SA-062-17
On some 2017 CX-5s, the Accessory Lighted Door Sill Trim Plate (DSTP) accessory may not light up after installation. This is likely caused by an incorrect magnet location. Read More »
-
TSB #SA-042-17
ON SOME 2017 CX-5 VEHICLES, THE DRIVERS DOOR IS SLIGHTLY HARDER TO CLOSE THAN THE OTHER DOORS. THIS OCCURS WHEN ALL THE OTHER DOORS AND WINDOWS ARE FULLY CLOSED. Read More »
STRUCTURE:BODY:HATCHBACK/LIFTGATE
-
TSB #09-006-24
Some vehicles may exhibit a creaking or clacking noise when operating the power lift gate (PLG). The noise may be caused by the following: Creaking noise: Dust and dirt accumulates on the sealing portion of the PLG drive unit, reducing ... Read More »
-
TSB #09-015-22
Some vehicles may exhibit corrosion on the liftgate lock striker. This may be caused by water penetrating from micro cracks existing on the lock striker's coating surface that reacts with zinc contained in the undercoating and produces ... Read More »
-
TSB #MT-006-18
POWER LIFTGATE INOPERATIVE WITH DTC U3003:16: Some customers may complain about an inoperative power liftgate (PLG) with DTC U3003:16 (Power liftgate (PLG) control module power supply voltage low input) is stored in memory. Read More »
STRUCTURE:BODY:TRUNK LID
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
STRUCTURE:BODY:HOOD
-
TSB #SA-040-19
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #SA-024-18
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
STRUCTURE:BODY:ROOF AND PILLARS
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
LATCHES/LOCKS/LINKAGES
-
TSB #09-006-24
Some vehicles may exhibit a creaking or clacking noise when operating the power lift gate (PLG). The noise may be caused by the following: Creaking noise: Dust and dirt accumulates on the sealing portion of the PLG drive unit, reducing ... Read More »
-
TSB #09-004-22a
Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
-
TSB #SA-050-22
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. Read More »
-
TSB #09-015-22
Some vehicles may exhibit corrosion on the liftgate lock striker. This may be caused by water penetrating from micro cracks existing on the lock striker's coating surface that reacts with zinc contained in the undercoating and produces ... Read More »
-
TSB #09-004/22
Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
-
TSB #09-015-21-3805
Some CX-5 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
-
TSB #09-019-20-3686
Some customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
VEHICLE SPEED CONTROL
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #09-034-18-3430a
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #09-034-18-3430
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
TIRES
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
-
TSB #MT-002-20
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
-
TSB #04-003-19-3589a
Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. Read More »
-
TSB #04-003-19-3589
Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #SA-073-17
Mazda is incorporating a "Direct" type TPMS, which is unlike the previous "Indirect" type system. With the "Direct" type TPMS........ ? there is no TPMS switch on the dashboard. It is no longer needed. Read More »
WHEELS
-
TSB #SA-022-24
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-031-23
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #02-002-21-3769a
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #02-002-21-3769
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #MT-002-20
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
-
TSB #02-004-20-3685
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #04-003-19-3589a
Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. Read More »
-
TSB #04-003-19-3589
Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. Read More »
-
TSB #SA-016-19
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #02-002-19-3546
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #02-008-18-3467
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-073-17
Mazda is incorporating a "Direct" type TPMS, which is unlike the previous "Indirect" type system. With the "Direct" type TPMS........ ? there is no TPMS switch on the dashboard. It is no longer needed. Read More »
TRAILER HITCHES
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #SA-003-18
Some repair kits (p/n 0000-8E-R09) for Recall 1617K (2017 CX-5 - EQUIPPED WITH A GENUINE MAZDA ACCESSORY TRAILER - HITCH HARNESS) may contain an extra wire harness (shown below). Read More »
SEATS
-
TSB #09-002-20-3667
Some customer may complain of warping on the driver and/or passenger side seat cushion trim, which may cause poor appearance complaints. Read More »
-
TSB #09-020-19-3524a
Some customer may complain of warping on the driver and/or passenger side seat cushion trim, which may cause poor appearance complaints. Read More »
-
TSB #09-020-19-3524
Some customer may complain of warping on the driver seat cushion trim, which may cause poor appearance complaints. Read More »
-
TSB #09-006-19-3563
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #09-015-18-3445a
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #09-013-18-3434
Some customers may complain about the driver and/or passenger rear side seat cushion trim (1) coming off the seat cushion frame. The front seat cushion trim (bottom rear) is attached to the seat cushion frame using a hook. Read More »
-
TSB #09-015-18-3445
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
SEATS:FRONT ASSEMBLY:POWER ADJUST
-
TSB #09-016-18-3428
Some customers may complain that the driver's seat does not automatically move to the programmed position when unlocking the driver's door with the remote transmitter unlock button (1), unless the button is pressed repeatedly (more than ... Read More »
SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER
-
TSB #MT-018-17
Some customers may complain about: PASSENGER Seat Belt and PASS AIRBAG OFF indicator lights ON (A). Front seat warmers ON (B) and cannot be turned OFF.No DTC's are stored in memory. Read More »
FORWARD COLLISION AVOIDANCE
-
TSB #15-002/22
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. Read More »
-
TSB #15-004-21-3835
NOTE: This Service Information is only applicable for vehicles equipped with a Forward Sensing Camera (FSC), KDD1-67-XCX and GSH7-67-XCX*. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #SA-003-19
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #15-001-19-3517a
Some vehicles may experience a SBS/SCBS, LAS/LDWS and/or ADAPTIVE LED headlight /HBC warning light on with the DTC U0155:00 stored in memory. The warning lights may stay on while these functions are deactivated. Read More »
FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
-
TSB #SA-056-17
Mazda Radar Criose Control (MRCC) system frequently asked questions (FAQ) Read More »
FORWARD COLLISION AVOIDANCE: SENSING SYSTEM
-
TSB #MT-016-17
The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with ... Read More »
-
TSB #SA-066-17
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA
-
TSB #15-002/22
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. Read More »
-
TSB #SA-037-20
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
-
TSB #SA-003-19
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). Read More »
-
TSB #SA-003-19
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #15-002-18-3502
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #SA-014-18
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: The ... Read More »
-
TSB #15-001-18-3369
Some customers may experience the following symptom relating to the Forward Sensing Camera (FSC)with DTC C1001:92 [Forward sensing camera (FSC) poor field of view] stored in memory.When the visibility out the windshieldis poor (i.e. Read More »
LANE DEPARTURE
-
TSB #15-001/22
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. Read More »
-
TSB #15-003-21-3828
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #15-001-19-3517a
Some vehicles may experience a SBS/SCBS, LAS/LDWS and/or ADAPTIVE LED headlight /HBC warning light on with the DTC U0155:00 stored in memory. The warning lights may stay on while these functions are deactivated. Read More »
-
TSB #RF-18-01R1
If one of the blind spot monitoring (BSM) control modules has to be replaced on a 2017-2018 CX-5, inspect the labels (1) and (2) on the modules (P/N KB8C-67-Y30E). Read More »
-
TSB #SA-053-17
Lane Departure Warning System (LDWS) frequently asked questions (FAQ) Read More »
LANE DEPARTURE: WARNING
-
TSB #SA-023-18
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
LANE DEPARTURE: BLIND SPOT DETECTION
-
TSB #15-001/22
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. Read More »
-
TSB #SA-013-18
Some customer's may complain that the blind spot monitoring (BSM) is not operating, and the key ON bulb check is OK with no DTCs stored in memory. Read More »
-
TSB #SA-054-17
Blind Spot Monitoring (Advanced BSM) system frequently asked questions (FAQ) Read More »
BACK OVER PREVENTION
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #09-032-19-3579
Some customers may experience improper operation of the rear parking system with beep sounds coming from the rear parking sensor when there are no obstacles behind the vehicle. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #08-004-16
M-MDS Data monitor displays incorrect air bag module resistance value. Read More »
BACK OVER PREVENTION: CAMERA SYSTEM
-
TSB #15-006-17-3388
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
INTERIOR LIGHTING
-
TSB #SA-062-17
On some 2017 CX-5s, the Accessory Lighted Door Sill Trim Plate (DSTP) accessory may not light up after installation. This is likely caused by an incorrect magnet location. Read More »
COMMUNICATION:MANUFACTURER TELEMATICS
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
EQUIPMENT
-
TSB #SA-008-24
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-036-23
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
-
TSB #RF-22-01R3
This Parts Flash replaces RF-22-01R2 released January 04, 2022. It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-23a
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #RF-22-01R2
This Parts Flash replaces RF-22-01R released November 21, 2022. It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-23
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #SA-016-22a
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method Read More »
-
TSB #SA-041-22
Some customers may complain about infotainment center display: Ghost touch, surface peeling, spider cracks. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #09-003-22a
Some vehicles may exhibit the following malfunctions: - The film on the center display is peeling off, as shown in the illustration below. This may be caused by cleaning the center display surface. Read More »
-
TSB #SA-026-22
Apple CarPlay / Android Auto Frequently Asked Questions (FAQs) Read More »
-
TSB #SA-016-22
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method Read More »
-
TSB #02-002/22
Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. Read More »
-
TSB #09-003/22
Some vehicles may exhibit the following malfunctions: 1. The film on the center display is peeling off, as shown in the illustration below. This may be caused by cleaning the center display surface. Read More »
-
TSB #15-002/22
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. Read More »
-
TSB #15-001/22
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #09-016-21-3797c
Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation ... Read More »
-
TSB #SA-019-21e
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns Read More »
-
TSB #SA-052-21
For improvement of electrical diagnosis, the SKYACTIV??A? Wiring Terminal Test Kits has been delivered all the dealers. Read More »
-
TSB #SA-050-21a
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. Read More »
-
TSB #07-004-21-3830
Some vehicles may exhibit insufficient A/C performance / insufficient airflow from vents or ducts. These concerns may be caused by an evaporator temperature sensor malfunction due to insufficient water-proofing. Read More »
-
TSB #SA-019-21d
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #MT-002-21
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
-
TSB #09-028-21-3748
Some customers may complain about a whistling noise heard from the top of the A-pillar area when driving at highway speeds. Read More »
-
TSB #04-004-21-3821
Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. Read More »
-
TSB #09-016-21-3797b
Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation ... Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #07-003-21-3825
Some vehicles may exhibit a squeaking noise from the blower motor while it is operating. This is caused by burrs that were not trimmed completely in the manufacturing process of the blower motor. Read More »
-
TSB #SA-019-21c
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-025-21-3824
This service bulletin provides information regarding the proper use of the driver??A?A?s floor mat to avoid any potential interference with the foot pedals. Read More »
-
TSB #09-021-21-3818
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
-
TSB #SA-030-21a
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Read More »
-
TSB #SA-041-21
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section ... Read More »
-
TSB #SA-029-21a
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #09-017-21-3808
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black under any temperature. Read More »
-
TSB #SA-034-21
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #SA-030-21
Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method Read More »
-
TSB #SA-029-21
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay??A?A? / Android Auto??A?A?, but it can be activated using MDARS. Read More »
-
TSB #SA-019-21a
MAZDA CONNECT Symptom Troubleshooting (6th Generation Vehicles). Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #CSP05c
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #CSP05d
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #07-001-21-3775
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #CSP05b
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #SA-004-20c
In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all ... Read More »
-
TSB #SA-047-20b
CRACKED REAR DIFFERENTIAL. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
-
TSB #CSP05a
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #CSP05
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #04-007-20-3713a
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #SA-071-20
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
-
TSB #SA-070-20
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #SA-047-20a
CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. Read More »
-
TSB #SA-069-20
ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.mazdausa.com Read More »
-
TSB #09-028-20-3733
Some vehicles may have a loose rear bumper reflector without any visible external damage to the rear bumper cover. Read More »
-
TSB #09-029-20-3732
Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become ... Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #09-006-20-3673a
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #MT-001-20
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #09-019-20-3686
Some customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
-
TSB #SA-041-20
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #04-005-20-3687
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. Read More »
-
TSB #SA-026-20
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Audio System, Bluetooth??A?, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux ... Read More »
-
TSB #09-006-20-3673
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #SA-005-20
THUMPING/RATTLING NOISE FROM ENGINE COMPARTMENT: Some customers may complain about an unusual thumping/rattling noise coming from the engine compartment. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #09-003-20-3671
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #01-017-19-3601
Some customers may complain about a vibration through the driver and passenger seats at idle in (D)rive and (R)everse when the engine rpm drops down to 550. This vibration is caused by: 1.5L The No.3 and No. Read More »
-
TSB #07-007-19-3638
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
-
TSB #09-031-19-3625
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #SA-029-19a
The database error discovered with IDS 114.00-114.02 release has been fixed with IDS 114.04 release and is now available for download. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #07-002-19-3616
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #SA-029-19
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
-
TSB #SA-027-19
ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/ Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-001-19b
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-013-19
MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. Read More »
-
TSB #SA-001-19a
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #09-007-19-3564a
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #SA-001-19a
APPLE CARPLAY? / ANDROID AUTO? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #00-001-19-3560
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #09-005-19-3562
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-007-19-3564
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-004-19-3543
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #SA-001-19
APPLE CARPLAY? / ANDROID AUTO? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #09-001-19-3553
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #SA-050-18
Some customers may complain that the navigation brand icons are no longer shown after a navigation SD card update. This is caused by a navigation map supplier software change. Customers can set preferences if needed. Read More »
-
TSB #SA-005-18
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Read More »
-
TSB #09-010-18-3440b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-011-18
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. Read More »
-
TSB #01-022-18-3528a
Some vehicles may exhibit an excessive body vibration/unusual noise when idling or driving after parking inextremely cold temperatures (-25?C/-13?F). NOTE: This excessive vibration does not occur if the engine mount rubber No. Read More »
-
TSB #00-001-18-3446a
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #00-003-18-3480a
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
-
TSB #09-014-18-3443a
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-020-18-3458b
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-021-18-3459a
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-034-18-3430a
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-004-18
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
-
TSB #SA-034-18
MAZDA CONNECT SYSTEM FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-031-18
When troubleshooting a radar unit, DO NOT swap it with another vehicle. Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Read More »
-
TSB #09-020-18-3458a
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-027-18-3420
Some vehicles may have a broken trunk board (2) strap (1). This may be caused by insufficient strap cover strength. To eliminate this concern, the material of the strap cover has been changed to increase the strength. Read More »
-
TSB #09-025-18-3479
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #09-023-18-3475
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #01-011-18-3456
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazdamodels, there is no key cylinder on the steering column. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #00-001-18-3446
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-008-18
Some customers may complain about the MAZDA CONNECT center display cracking (spider cracking). The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display. Read More »
-
TSB #MT-003-18
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
-
TSB #SA-073-17
Mazda is incorporating a "Direct" type TPMS, which is unlike the previous "Indirect" type system. With the "Direct" type TPMS........ ? there is no TPMS switch on the dashboard. It is no longer needed. Read More »
-
TSB #02-009-17-3392
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold. Read More »
-
TSB #MT-018-17
Some customers may complain about: PASSENGER Seat Belt and PASS AIRBAG OFF indicator lights ON (A). Front seat warmers ON (B) and cannot be turned OFF.No DTC's are stored in memory. Read More »
-
TSB #SA-069-17
If you receive a customer complaint of an excessive gap between decoration panel and switch panel (as shown below), repair it according to the repair procedure below. Read More »
-
TSB #MT-017-17
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #MT-009-17
Some vehicles may exhibit a chattering noise from the rear spoiler (A) while driving on a rough road. This may be caused by loose rear spoiler installation nuts. Read More »
-
TSB #MT-005-17
SOME VEHICLES EQUIPPED WITH MAZDA RADAR CRUISE CONTROL (MRCC) WILL NOT SET (THE SYSTEM STAYS ON STANDBY) IF THE DRIVER'S SEAT BELT IS NOT FASTENED. THIS IS A NORMAL CONDITION. DO NOT PERFORM ANY REPAIRS FOR THIS CONDITION. Read More »
-
TSB #SA-037-17
RECALL 0516J UPDATED REPAIR PROCEDURE Read More »
-
TSB #SA385
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. Read More »
-
TSB #SA266
MAZDA Mobile start (MMS) cannot communicate with vehicle Read More »
-
TSB #00-004-16-3237
RAISING A VEHICLE WITH A JACK CAN BE DANGEROUS IF NOT DONE PROPERLY. THE VEHICLE CAN SLIP OFF THE JACK AND SERI-OUSLY INJURE SOMEONE. IN THIS SERVICE INFORMATION, SOME IMPORTANT WARNINGS AND CAUTIONS HAVE BEEN TAKEN FROM THE OWNER?S MANUAL. Read More »
-
TSB #MTI_1111
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. Read More »
EQUIPMENT:ELECTRICAL
-
TSB #09-028-23
Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Read More »
-
TSB #SA-016-23
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method Read More »
-
TSB #SA-008-21
DTC P0942:49 is missing from the Workshop Manual on MGSS. Follow the repair procedure below to repair the vehicle until the information is added. Read More »
-
TSB #SA-026-20a
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-012-20-3681
Some customers may complain about a high frequency noise (like a mosquito sound) while the active driving display is in the flip-up position. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #09-020-18-3458b
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #MT-008-18
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
-
TSB #09-020-18-3458
Some vehicles may exhibit BLUETOOTH? hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH? hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program ... Read More »
-
TSB #MT-001-18
When installing a navigation SD card, the center display may show error message "Invalid SD Card". Read More »
-
TSB #SA-036-17
IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version. Read More »
-
TSB #SA-065-17
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth?, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, ... Read More »
-
TSB #MT-015-17
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #SA-063-17
Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. Read More »
-
TSB #SA-049-17
There are a few issues with the accessory C960-V7-620 remote start kit instructions. In the current ?Registration (programming) of the controller? instructions, step 5shows an incorrect image. The function button is the lower button. Read More »
-
TSB #09-017-17
Audio, navigation and phone concerns with Mazda connect Infotainment system. All Mazda connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready step 3 process. Read More »
-
TSB #08-002-17-3312
When monitoring the resistance of the air bag modules and pre-tensioner seat belts, the Mazda Modular Diagnostic System (M-MDS) may display a value of only 1/100th of the actual resistance value. Read More »
EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #09-025-18-3479
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #09-023-18-3475
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #SA-005-18
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Read More »
EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
-
TSB #SA-046-21
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #09-003-18-3405b
Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. Read More »
-
TSB #09-001-18-3387
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during coldtemperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. Read More »
EQUIPMENT:ELECTRICAL:INFOTAINMENT
-
TSB #SA-001-23a
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #RF-22-01R2
This Parts Flash replaces RF-22-01R released November 21, 2022. It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-23
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: * Ghost Touch * DTC B108E:04 may be stored (Touch screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White ... Read More »
-
TSB #SA-041-22
Some customers may complain about infotainment center display: Ghost touch, surface peeling, spider cracks. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit. Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-021-21-3818a
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
-
TSB #09-017-17
Audio, navigation and phone concerns with Mazda connect Infotainment system. All Mazda connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready step 3 process. Read More »
EQUIPMENT:ELECTRICAL:INFOTAINMENT:VIDEO (TOUCH)SCREEN/MONITOR/UNIT
-
TSB #22-01R
Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Read More »
-
TSB #RF-22-01
Some customers may complain about infotainment center display ghost touch (touch screen operates by itself), surface peeling or spider cracks. Repair kits are available to replace just the screen. Read More »
EQUIPMENT:MECHANICAL
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
EQUIPMENT:OTHER:LABELS
-
TSB #RF-18-01R1
If one of the blind spot monitoring (BSM) control modules has to be replaced on a 2017-2018 CX-5, inspect the labels (1) and (2) on the modules (P/N KB8C-67-Y30E). Read More »
-
TSB #RF-18-01
If one of the blind spot monitoring (BSM) control modules has to be replaced on a 2017-2018 CX-5, inspect the labels (1) and (2) on the modules (P/N KB8C-67Y30E). Read More »
EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
-
TSB #SA-014-22
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. Read More »
-
TSB #01-003/22
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #MT-003/22
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-036-20
The owner??A?A?s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Read More »
-
TSB #SA-034-20
DTC P0942:49 TROUBLESHOOTING: P0942:49 is missing from the Workshop Manual on MGSS. Follow the repair procedure below to repair the vehicle until the information is added to the Workshop Manual. Read More »
-
TSB #00-001-18-3446a
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-009-18
The navigation SD Card VIN-locks to a vehicle in the following conditions: 1. Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Read More »
-
TSB #SA-001-18
The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. Read More »
-
TSB #MT-021-17
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
-
TSB #09-035-17-3080
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #SA-041-17
PERMANENT DTCS ARE NOW DISPLAYED WITH THE IDS 104 UPDATE. THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. Read More »
-
TSB #SA-040-17
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING ADVANCED KEYLESS ENTRY SYSTEM MALFUNCTIONS: (1) KEY FOB AND/OR DOOR REQUEST SWITCH DOES NOT OPERATE. Read More »
EQUIPMENT ADAPTIVE/MOBILITY
-
TSB #SA-027-24
Some customers may complain about infotainment center display. Peeling, spider cracks and white dots. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #02-002/22
Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. Read More »
-
TSB #15-004-21-3835
NOTE: This Service Information is only applicable for vehicles equipped with a Forward Sensing Camera (FSC), KDD1-67-XCX and GSH7-67-XCX*. Read More »
-
TSB #SA-019-21e
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns Read More »
-
TSB #15-003-21-3828
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. Read More »
-
TSB #04-004-21-3821
Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #15-002-21-3812
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #SA-019-21a
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-017-21-3808
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black under any temperature. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #MT-006-20
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #SA-047-20b
CRACKED REAR DIFFERENTIAL. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. Read More »
-
TSB #09-036-20-3756
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH??A? hands-free unit or text messaging related concerns. Read More »
-
TSB #SA-047-20a
CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. Read More »
-
TSB #09-030-20-3740
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #09-028-20-3733
Some vehicles may have a loose rear bumper reflector without any visible external damage to the rear bumper cover. Read More »
-
TSB #09-029-20-3732
Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become ... Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #09-015-20-3698b
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #09-015-20-3698
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #04-005-20-3687
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. Read More »
-
TSB #SA-037-20
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
-
TSB #SA-011-20a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #01-002-20-3678
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-011-20
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #09-002-20-3667
Some customer may complain of warping on the driver and/or passenger side seat cushion trim, which may cause poor appearance complaints. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #01-017-19-3601
Some customers may complain about a vibration through the driver and passenger seats at idle in (D)rive and (R)everse when the engine rpm drops down to 550. This vibration is caused by: 1.5L The No.3 and No. Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #15-001-19-3517a
Some vehicles may experience a SBS/SCBS, LAS/LDWS and/or ADAPTIVE LED headlight /HBC warning light on with the DTC U0155:00 stored in memory. The warning lights may stay on while these functions are deactivated. Read More »
-
TSB #09-002-19-3554
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. Read More »
-
TSB #09-019-18-3450
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. Read More »
-
TSB #MT-015-17
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #SA-064-17
Some customers may complain about one or more warning lights on when they start the vehicle during hot weather. The combination of warning lights mentioned by the customer may include: SCBS, LDWS, HBC. Read More »
-
TSB #MT-009-17
Some vehicles may exhibit a chattering noise from the rear spoiler (A) while driving on a rough road. This may be caused by loose rear spoiler installation nuts. Read More »
-
TSB #MT-003-17
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. Read More »
EQUIPMENT:APPLIANCE:AIR CONDITIONER
-
TSB #07-004-21-3830
Some vehicles may exhibit insufficient A/C performance / insufficient airflow from vents or ducts. These concerns may be caused by an evaporator temperature sensor malfunction due to insufficient water-proofing. Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #07-002-19-3616
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #07-002-18-3432
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #07-007-17-3384
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a clogged heater unit. Read More »
UNKNOWN OR OTHER
-
TSB #SA-027-24
Some customers may complain about infotainment center display. Peeling, spider cracks and white dots. Read More »
-
TSB #07-003-24
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #MT-001-22
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
-
TSB #SA-058-19
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »