The TSB information displayed below are summaries. Unfortunately we do not have access to the full versions.
To get full information about a particular TSB, write down the TSB title & date, & either contact your local dealer or click on the links below.
Summary: This Preliminary information communicates the possibility of the high pressure fuel pump roller follower pin walking out and making contact with cylinder head causing the ignition timing to be serverly retarded on acceleration causing lack
Summary: This Preliminary information communicates the Control Valve Body spacer plate orifice #33 may be restricted as root cause for themay not go above 30 mph, may be stuck in 2nd gear, will not upshift, MIL is on, and/or DTC P2821 concern,to rep
Summary: This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
Summary: This Preliminary information communicates the possibility of the high pressure fuel pump roller follower pin walking out and making contact with cylinder head causing the ignition timing to be serverly retarded on acceleration causing lack
Summary: This Technical bulletin provides information for rear brake pad replacement to correct a squeak type noise heard from the rear brakes when cold.
Summary: 18308 - Customer Satisfaction Program - Certain vehicles, may have a condition in which the right-hand knuckle wheel speed sensor (WSS) hole is machined approximately 1.6mm off location. The WSS is positioned too far away from the wheel bea
Summary: This Preliminary Information communication provides information to the technician about vehicles that have a crank but engine does not start concern.Technician will use this publication to reset the battery low state of charge concern after
Summary: This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
Summary: This Preliminary information communicates to the dealer an issue where the vehicle's service engine soon light may illuminate due to trouble codes P0601-P0604, P0606, P062B, P062F, P0630, P16F3, or P262B . The dealer is to inspect the engin
Summary: This Preliminary Information communication provides information to the technician about vehicles that have unwanted engine flairs while the vehicle is at steady state speed or while the vehicle is slowing. Dealer should communicate to the c
Summary: This Preliminary information communicates to the technician where to find the engine identification tag and what information on that tag to use during programming of someengine control modules.
Summary: This Preliminary information communicates additional diagnostics to assist the dealer technician with diagnosing and repairing trouble code P2097.
Summary: This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to call General Motors T
Summary: This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position.
Summary: This Preliminary Information communication provides information to the technician about vehicles that have a crank but engine does not start concern.Technician will use this publication to reset the battery low state of charge concern after
Summary: This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician i
Summary: This Preliminary information communicates the Control Valve Body spacer plate orifice #33 may be restricted as root cause for themay not go above 30 mph, may be stuck in 2nd gear, will not upshift, MIL is on, and/or DTC P2821 concern,to rep
Summary: This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blo
Summary: This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may
Summary: This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Smoke or Burning Odor from Underhood with Malfunction Indicator Lamp Illuminated with DTC P305F or P058D
Summary: This technical bulletin provides a procedure to reprogram the ECM to correct a condition of Malfunction Indicator Illuminated with DTC P2B95 Set due to a calibration concern.
Summary: This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
Summary: This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of asse
Summary: This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
Summary: 18017 - Service Update. An ASIC (Application Specific Integrated Circuit) in the engine control module may not power up correctly preventing the main microprocessor from communicating with ASICs. This can result in a no start, no crank an
Summary: This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is
Summary: This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related component
Summary: This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
Summary: This Preliminary information communicates the following to the dealer. If an engine oil leak has been isolated to the front crankshaft seal, check for misfires low engine compression and/or cylinder leakage readings. These issues could caus
Summary: This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request.
Summary: This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blo
Summary: This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to call General Motors T
Summary: This informational bulletin explains the need to change the oil used in the LFV, LE2 engines, to a dexos 1 full synthetic to avoid piston damage.
Summary: This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to call General Motors T
Summary: This Preliminary Information communication provides the technician with the diagnosis and repair steps for a vehicle with a check engine light on with Diagnostic Trouble Code P015B or a reduced engine power message with Diagnostic Trouble C
Summary: This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to call General Motors T
Summary: This Preliminary information communicates the possibility of the timing chain tesnioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE.
Summary: This Preliminary Information communication provides information to the technician about vehicles that have smoke from exhaust system and a coolant loss. Technician will need to replace the Exhaust Heat Exchanger assembly if signs of coolant
Summary: This Preliminary information communicates to the technician steps to address the MIL concern on the listed vehicles. It advises that if the vehicle has the code stored, the tech is to perform the SI diagnostic. If the diagnostic fails to is
Summary: This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request.
Summary: This technical bulletin provides a procedure to install a anti rattle spring on the actuator arm for the turbo and to correct the customers concern of a rattle noise heard from front of the engine.
Summary: This technical bulletin provides a procedure to inspect the A/C heat exchanger for possible weak welds, that may leak refrigerant causing the A/C system to not work properly.
Summary: This Preliminary Information communication provides information to the technician related to utilizing crankcase pressure testing to aid in engine oil leak diagnostics. The technician is directed to perform the testing and to check related
Summary: This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
Summary: This Preliminary information communicates to the dealer that the turbocharger wastegate actuator - rod assembly should be replaced as an individual component if found to be broken or damaged. That complete turbocharger replacement is not re
Summary: This technical bulletin provides a procedure to fill the cooling system if a customer experiences a condition of Gurgle or Water Rush Noise from Dash Area Upon a Stop due to the system not being filled all the way.
Summary: This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position.
Summary: This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician i
Summary: This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician i
Summary: 18239 - Emissions Recall - General Motors has decided to conduct a Voluntary Emission Recall involving certain 2018 model year vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). On some vehicles, an
Summary: This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position.
Summary: This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
Summary: This technical bulletin provides a procedure for connector kit and ambient air temperature sensor harness replacement due to active shutters being inoperative.
Summary: This Preliminary information communicates the possibility of the high pressure fuel pump roller follower pin walking out and making contact with cylinder head causing the ignition timing to be serverly retarded on acceleration causing lack
Summary: This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
Summary: This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
Summary: This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
Summary: This bulletin provides procedure information for hard to fuel and/or fuel filling station nozzle shuts off repeatedly due to the vapor generation reduction device inside the fuel filler pipe.
Summary: This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
Summary: This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up.
Summary: This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
Summary: This technical bulletin provides information for new software available to correct the reading of the fuel from dropping from full quickly after fill up.
Summary: This Preliminary Information communication advises the technician that the Malibu 5ET50 Hybrid Transmission and Component has a part restriction program. The dealer will need to call General Motors Technical Assistance Center (Technical Ass
Summary: This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Technician will find Diagnostic Trouble Codes P1AEE, P1AEF, P1AF0, P1AF2, a
Summary: This Preliminary information communicates the Control Valve Body spacer plate orifice #33 may be restricted as root cause for themay not go above 30 mph, may be stuck in 2nd gear, will not upshift, MIL is on, and/or DTC P2821 concern,to rep
Summary: This Preliminary Information communication advises the technician that the Product Quality Center has ended the part restriction for the T87A Transmission Control Module.
Summary: This Preliminary information communicates the Control Valve Body spacer plate orifice #33 may be restricted as root cause for themay not go above 30 mph, may be stuck in 2nd gear, will not upshift, MIL is on, and/or DTC P2821 concern,to rep
Summary: This technical bulletin provides a procedure to have the valve body spacer plate replacement and transmission control module reprogramming with the latest software.
Summary: This Preliminary Information communication advises the technician that the Malibu 5ET50 Hybrid Transmission and Component has a part restriction program. The dealer will need to call General Motors Technical Assistance Center (Technical Ass
Summary: 18017 01 - Service Update. An ASIC (Application Specific Integrated Circuit) in the engine control module may not power up correctly preventing the main microprocessor from communicating with ASICs. This can result in a no start, no crank
Summary: This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is
Summary: This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
Summary: This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Technician will find Diagnostic Trouble Codes P1AEE, P1AEF, P1AF0, P1AF2, a
Summary: This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the T87A Transmission Control Module. The dealer technician is advised to call the GM Product Quality Center for fu
Summary: This Preliminary Information communication advises the technician that the Malibu 5ET50 Hybrid Transmission and Component has a part restriction program. The dealer will need to call General Motors Technical Assistance Center (Technical Ass
Summary: This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Technician will find Diagnostic Trouble Codes P1AEE, P1AEF, P1AF0, P1AF2, a
Summary: This Preliminary Information communication advises the technician that the Malibu 5ET50 Hybrid Transmission and Component has a part restriction program. The dealer will need to call General Motors Technical Assistance Center (Technical Ass
Summary: 18277 - Customer Satisfaction Program - Certain vehicles equipped with RPO MNH (6 Speed Automatic Transmission) may have been built without a transmission case assembly cup plug. As a result, lubrication flow within the transmission may be
Summary: This Preliminary information communicates the Control Valve Body spacer plate orifice #33 may be restricted as root cause for themay not go above 30 mph, may be stuck in 2nd gear, will not upshift, MIL is on, and/or DTC P2821 concern,to rep
Summary: This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of asse
Summary: This Preliminary information communicates to replace the valve body and solenoid body assemblies with both spacer plates for a DTC P2820concern if not able to clean the valve body or solenoid body assemblies.
Summary: This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Shift to Park Message Displayed.
Summary: This engineering informational bulletin is requesting information from the filed on vehicles that have the condition of Shift to Park Message Displayed.
Summary: This Preliminary information communicates to look for other codesP0AEE, P0AF3, P0BD2, P0BD7, P0BDC, P0BE1 if a customer comes in with a Mil Request.
Summary: This Preliminary Information communication provides the technician with inspection and repair instructions for vehicles with Service Engine Soon lamp when locking, unlocking, going into gear, and when vehicle is running. If service rear cam
Summary: This Preliminary information communicates the possibility of the high pressure fuel pump roller follower pin walking out and making contact with cylinder head causing the ignition timing to be serverly retarded on acceleration causing lack
Summary: This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to call General Motors T
Summary: This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Th
Summary: This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may
Summary: This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Th
Summary: This technical bulletin provides a procedure to replace the HMI module to correct a condition of Radio Control (ICS) Display Does Not Remain Off at Times after it Has Been Turned Off in the Radio Settings Menu due to a software concern.
Summary: This technical bulletin provides a procedure to perform diagnostics on the codes set and if no problem is found, to replace either the input or output speed sensor.
Summary: This technical bulletin provides a procedure to reprogram the memory set module to correct a condition of Personalization Selections Intermittently Missing from Comfort and Convenience Menu due to a calibration concern.
Summary: This technical bulletin provides a procedure to have the valve body spacer plate replacement and transmission control module reprogramming with the latest software.
Summary: This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
Summary: This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technic
Summary: 18017 01 - Service Update. An ASIC (Application Specific Integrated Circuit) in the engine control module may not power up correctly preventing the main microprocessor from communicating with ASICs. This can result in a no start, no crank
Summary: 18017 - Service Update. An ASIC (Application Specific Integrated Circuit) in the engine control module may not power up correctly preventing the main microprocessor from communicating with ASICs. This can result in a no start, no crank an
Summary: 18009 - Service Update. The bootloader version for the engine control module (ECM) was incorrectly released, and may result in a no-start or stall, and P062B, P0171/P0172, P1133/P2195/P2196 or P300 diagnostic trouble codes to set. Dealers a
Summary: This technical bulletin provides a procedure for connector kit and ambient air temperature sensor harness replacement due to active shutters being inoperative.
Summary: This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble
Summary: This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehic
Summary: This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
Summary: This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technic
Summary: This Preliminary information communicates a false setting of DTCU0121 in the FVCM due to a FVCM software anomaly. Code U0121 will set and be moved to history in the FVCM with each ignition cycle.
Summary: This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138
Summary: This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technic
Summary: This Preliminary Information communication provides information to the technician about vehicles that have a Shift to Park message on the Driver Information Center. Technician will find Diagnostic Trouble Codes P1AEE, P1AEF, P1AF0, P1AF2, a
Summary: This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availabilit
Summary: This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understand
Summary: This informational bulletin provides to the technician, locations to check for possible loose or damaged electrical connections that may set a DTC instead of just replacing a part.
Summary: This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2.
Summary: This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system.
Summary: This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern i
Summary: This Preliminary Information communication advises the technician the High Voltage Drive Motor Battery, for the 2016-2018 Chevrolet Malibu Hybrid has been placed on a parts restriction. Dealer will need to call General Motors Technical Assi
Summary: This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Smoke or Burning Odor from Underhood with Malfunction Indicator Lamp Illuminated with DTC P305F or P058D
Summary: This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
Summary: 18017 - Service Update. An ASIC (Application Specific Integrated Circuit) in the engine control module may not power up correctly preventing the main microprocessor from communicating with ASICs. This can result in a no start, no crank an
Summary: This Preliminary Information communication advises the technician the High Voltage Drive Motor Battery, for the 2016-2018 Chevrolet Malibu Hybrid has been placed on a parts restriction. Dealer will need to call General Motors Technical Assi
Summary: This informational bulletin explains how the technician no longer needs to perform the 3 hour battery relearn procedure on 2017-2018 vehicles with Start/Stop.
Summary: This Preliminary information communicates the possibility for a internal E88 ECM issue that can cause numerous ECM related codes including dtc p0606 and the vehicle may crank and not start or not crank.
Summary: This Preliminary information communicates to replace the valve body and solenoid body assemblies with both spacer plates for a DTC P2820concern if not able to clean the valve body or solenoid body assemblies.
Summary: This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Th
Summary: This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/
Summary: This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odomete
Summary: This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Th
Summary: This technical bulletin provides a procedure to reprogram the ECM to correct a condition of Malfunction Indicator Illuminated with DTC P2B95 Set due to a calibration concern.
Summary: This technical bulletin provides information for new software available to correct the reading of the fuel from dropping from full quickly after fill up.
Summary: This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
Summary: This Preliminary information communicates a false setting of DTCU0121 in the FVCM due to a FVCM software anomaly. Code U0121 will set and be moved to history in the FVCM with each ignition cycle.
Summary: This technical bulletin provides a procedure to reprogram the cluster to correct a condition of Intermittent Blank/Missing Driver Information Center Info Pages Upon Start Up due to a software abnormality.
Summary: This Preliminary information communicates thata vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. The technician may attempt to program the Active Safety Control Module (ASCM) and encount
Summary: This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the T87A Transmission Control Module. The dealer technician is advised to call the GM Product Quality Center for fu
Summary: This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface contro
Summary: This Preliminary information communicates thata vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. The technician may attempt to program the Active Safety Control Module (ASCM) and encount
Summary: This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
Summary: This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed.
Summary: This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
Summary: This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
Summary: This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse o
Summary: This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse o
Summary: This Preliminary information communicates to replace the valve body and solenoid body assemblies with both spacer plates for a DTC P2820concern if not able to clean the valve body or solenoid body assemblies.
Summary: This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
Summary: This Preliminary information communicates the Control Valve Body spacer plate orifice #33 may be restricted as root cause for themay not go above 30 mph, may be stuck in 2nd gear, will not upshift, MIL is on, and/or DTC P2821 concern,to rep
Summary: This Preliminary Information communication provides information to the technician that some owners may notice at roughly 3/4 of the way through the accelerator pedal travel there is a click felt in the pedal also the pedal gets harder to pu
Summary: This Preliminary information communicates that a vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. The technician may attempt to program the Active Safety Control Module (ASCM) and encoun
Summary: This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Cover
Summary: This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehic
Summary: This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
Summary: This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed fo
Summary: This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided.
Summary: This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
Summary: This technical bulletin provides repair information to correct a customer concern of front seat slight rocking movement while shifting weight from seat, during hard stops, and/or when driving over rough road surface.
Summary: This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
Summary: This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
Summary: This Preliminary information communicates that a vehicle may exhibit a Adaptive Cruise Control Unavailable and/or Lane Keep Assist Unavailable message. The technician may attempt to program the Active Safety Control Module (ASCM) and encoun
Summary: This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble
Summary: This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble
Summary: This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble
Summary: This Preliminary Information communication provides the technician with inspection and repair instructions for vehicles with Service Engine Soon lamp when locking, unlocking, going into gear, and when vehicle is running. If service rear cam
Summary: This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
Summary: This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse o
Summary: This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previousl
Summary: This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Th
Summary: This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to sen
Summary: This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for
Summary: This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. The
Summary: This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical Assista
Summary: This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Ap
Summary: This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim.
Summary: This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
Summary: This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related component
Summary: This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
Summary: This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that e
Summary: This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
Summary: This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
Summary: This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
Summary: This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availabilit
Summary: This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2.
Summary: This Preliminary Information communication advises the technician that the drive motor generator control module is being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to call General Motors T
Summary: This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
Summary: This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up.
Summary: This informational bulletin explains the need to change the oil used in the LFV, LE2 engines, to a dexos 1 full synthetic to avoid piston damage.
Summary: This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. The
Summary: This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone cont
Summary: This engineering information is requesting information from the field on vehicles that have the condition of Speaker Rattle, Speaker Crackle, Poor Sound Quality, Speaker Pop, or Speaker Distortion.
Summary: This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
Summary: This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer t
Summary: This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
Summary: This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.
Summary: The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
Summary: This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2.
Summary: The PI was created to advise of an engineering investigation for a concern of unable to connect toOnStar Virtual Advisor when selecting "New Destination" in the OnStar menu.
Summary: This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information
Summary: This Preliminary information communicates that acustomer may complain of the Driver Information Center(DIC) intermittently flickering or going blank. It may be noted that this only seems to occur when playing songs via IHeart or Pandora. Th
Summary: This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. The
Summary: This technical bulletin provides a procedure to replace the HMI module to correct a condition of Radio Control (ICS) Display Does Not Remain Off at Times after it Has Been Turned Off in the Radio Settings Menu due to a software concern.
Summary: This technical bulletin provides a procedure to test the radios receiver if certain XM channels cut out (mutes) depending on location of the vehicle.
Summary: This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical Assista
Summary: This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technic
Summary: This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical Assista
Summary: This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motor
Summary: This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU
Summary: This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technic
Summary: This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technic
Summary: This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
Summary: This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availabilit
Summary: This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motor
Summary: This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have hi
Summary: This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have hi
Summary: This technical bulletin provides a procedure to inspect the A/C heat exchanger for possible weak welds, that may leak refrigerant causing the A/C system to not work properly.
Summary: This Preliminary information communicates to the technician where to find the engine identification tag and what information on that tag to use during programming of someengine control modules.
Summary: This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
Summary: This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician i
Summary: This Preliminary information communicates additional diagnostics to assist the dealer technician with diagnosing and repairing trouble code P2097.
Summary: This Preliminary information communicatesthe steps to diagnose and repair the concern of MIL on with DTC'sP0335 P0340 P0365 set current or in history. The Technician is advised to Perform theBattery Inspection / Test in Service Informat
Summary: This Preliminary Information communication advises the technician that the Malibu 5ET50 Hybrid Transmission and Component has a part restriction program. The dealer will need to call General Motors Technical Assistance Center (Technical Ass
Summary: This Preliminary information communicates that the E88 ECM controllers part number 12680194 and 12691559 are currently under part restriction.
Summary: This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previousl
Summary: This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to sen
Summary: This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for
Summary: This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone cont